 |
| (Click on photos to enlarge) |
slisen.blogspot.com
Today I’m showing how I paint a skein of yarn to
achieve a variegated yarn.
In this case,
I only wanted 2 shades of the same color with short spans but you can use any
amount of colors, in whatever length your pattern calls for.
1.
First
off, my yarn came from a cone so I wound the yarn into a skein with my DIY
niddy noddy.
I have 3 different shaft
lengths to make 3 different length skeins.
Instructions for making your own niddy noddy with PVC pipe can be found
at
http://www.theanticraft.com/book/lostpages/niddy.htm.
It works great and doesn’t cost a fortune.
Be sure to tie off the yarn with figure 8’s
so it doesn’t get tangled in the dyeing process.
And I tie a long strand of yarn thru and
around the skein which comes in handy for lifting the skein when wet and also
keeps it from tangling.
2.
Wet the
yarn skein by ‘laying’ it on top of lukewarm water in a sink or pail.
Do not force the yarn into the water but let
it soak up and submerge by itself.
Depending on the yarn and/or how it’s wound, the air bubbles that could be trapped by forcing it into the water may create resists to prevent the dye from
being absorbed evenly.
3.
After
the entire skein of yarn has been submerged by itself in the water, add a
squirt of Dawn dishsoap or Synthrapol to the water and gently sozzle the
yarn.
This releases any oil residue in
the yarn.
Gently, rinse with lukewarm
water and let soak in fresh water for atleast 30 minutes.
4.
While
the yarn is soaking, prepare the dyes according to manufacturer’s directions
and prepare the work surface.
I use a
painter’s plastic drop cloth to cover my whole working area.
Then I lay down 2 long sheets of plastic wrap
over the drop cloth.
When I’m painting
with dyes, I add a couple tsp of white vinegar to the dye solution before
applying to the yarn.
Certainly follow your
manufacturer’s instructions for adding vinegar (acid), but when I’m vat dyeing
in my crockpot, I always add the vinegar at the end of the process
after the required temperature has been
maintained for 30 minutes.
5.
After
soaking the yarn for atleast 30 minutes, remove it from the water and gently
squeeze (do not wring) to remove the water.
I use an old bath towel to wrap around the skein, lay it on the floor
and walk on it.
The more water that can
be removed before applying the dyes, the less the dyes will run into each
other.
Lay the skein onto the prepared
work surface with the seam of the plastic wrap running down thru the
middle.
This plastic wrap will be used
later to wrap the dyed skein for heating.
6.
Now the
fun begins.
Wear rubber gloves! Apply
dye to the yarn in whatever pattern you like.
I prefer to use foam sponges but a squeeze bottle, syringe or anything
of the like can be used to apply the dye.
Use your fingers to work in the dye as you work.
From experience, I’ve learned to apply the
dark colors first, then fill in with lighter colors.
The colors will run together and if the dark
color is already there, the lighter color won’t make much of a difference to
it.
But a dark color merging into a
lighter color will change the color or intensity of the lighter one.
Also be choosy about the colors you put next
to each other.
If you don’t want any
green in your yarn, don’t put yellow and blue next to each other.
7.
Carefully
turn the skein over to see if the back has been saturated with color.
If not to your liking, turn the whole skein
over and apply more dye to that side.
I
wanted a tonal quality so I wasn’t real concerned about the backside but I
didn’t want any white either, so I did turn my skein over and applied more
dye.
If you want a solid color, blot up
excess water with paper towels as you work.
Yarn that is
saturated with water
won’t take dye real well.
8.
When
your dyeing is to your liking, blot up excess water with layers of paper
towels.
Check your work.
If you want more color or more even color,
blot up as much water as you can and reapply more dye.
Again, blot up excess water before wrapping
for heat setting.
9.
Use the
2 sheets of plastic wrap that you’ve been working on to wrap around the yarn
skein, wrapping half of the skein with one sheet and the other half with the
other.
Don’t wrap it with one sheet of
plastic as you don’t want the colors from each section touching each
other.
You may need to use another sheet
of plastic to wrap the ends.
Yarn should
not be directly exposed to steam or heat.
10.
I use a
7 qt crockpot for heat setting. In this case, steam will be used.
I have a little DIY rack that fits in the
bottom of my crockpot to elevate the yarn over the water.
Don’t let the yarn sit in water, it’ll dilute
the colors.
Put enough warm water in the
crockpot to boil, my rack is about 4” tall.
I like using a crockpot because most dye manufacturer's recommend a gradual rise in heat. I've never had a dye failure using my crockpot.
11.
Turn
the crockpot on high and let heat til the water simmers.
Temperature of the yarn should reach about
200 degrees for atleast 30 minutes.
After 30 minutes, turn the crockpot off and let the yarn cool on its own
to a temperature that will allow handling.
When cool enough to comfortably handle, unwrap the yarn and carefully
rinse with the same temperature water as the yarn.
Use a squirt of Dawn dishwashing liquid or
Synthrapol to remove any excess dye that hasn’t bonded to the yarn.
Rinse til the water runs clear.
Squeeze, remember not to wring, the yarn and
wrap in a towel again, walk on it and hang to dry.
12.
When
the yarn is completely dry, wind it into a cake and you’re ready to create and
take pleasure in a project made with your own dyed yarn.
